When you need a masonry veneer contractor Milwaukie OR homeowners actually keep on speed dial, RenovoBase handles brick, stone, and cast stone veneer from tear-off to final joint. We have served Milwaukie and Clackamas County since 2021, and we build every wall to shed Oregon rain instead of soaking it up. Call (855) 947-9500 for a same-week walkthrough.
Tell us what is happening. Our local team will confirm your visit shortly.
Call Now (855) 947-9500 → No spam. No obligation. Just practical help.
A masonry veneer contractor Milwaukie OR installs a non-structural outer skin of brick, stone, or cast stone over wood frame, concrete block, or existing walls. The veneer carries no roof load, but it does carry the weather. We set a drainage plane, flashing, weep holes, and a mortar mix matched to the material so water exits the wall instead of sitting behind it. Done right, a veneer wall lasts 50 years or more.
Milwaukie sits in a wet, mild pocket of Clackamas County where freeze-thaw cycles are short but rain is relentless. That combination punishes bad flashing and soft mortar. If your 1960s ranch home has spalling brick or efflorescence blooming every spring, you are seeing water infiltration, not just cosmetic wear. We handle masonry veneer installation Milwaukie homeowners call for after a bad winter, and we quote the repair before we quote the rebuild.
Every veneer project starts with the same core scope. Add-ons like custom arches or cast stone sills are quoted separately so you can see exactly what you are paying for.
We remove old siding, lath, and failed flashing, then haul it away. If we find rot or a cracked foundation behind the wall, we stop and show you before covering it up.
House wrap, a drainage plane, and corrosion-resistant flashing at every head, sill, and roof-to-wall joint. This is the layer that keeps water out of your framing.
We anchor veneer with corrosion-resistant ties and reinforcing steel set to IBC spacing. No nailed-on brick, no shortcuts behind the wall.
Brick, natural stone veneer, or cast stone set on a mason's line with a mortar mix matched to the material. We cut with a wet saw and an angle grinder for tight corners and arches.
Weep holes at 24 inches on center at the base course, then tooled joints finished with a jointing tool while the mortar is still green. This is what makes the wall shed water and look finished.
We wash the wall down, walk the job with you, and hand over a photo record of the flashing and tie details. You know what is behind the brick because you have seen it.
We walk the wall with you, check for cracked foundation, settling, or brick veneer detachment, and photograph the problem areas. You get a written scope and a price range the same day, usually within two hours of the visit. No charge for the estimate.
We bring samples from Glen-Gery, Boral, and Mutual Materials so you can see brick and stone against your actual siding in real daylight. We confirm mortar color, joint profile, and whether you want a cast stone sill or lintel. This step takes one meeting, not three.
Old siding, rotted sheathing, and failed flashing come off first. We install new house wrap, a drainage plane, and corrosion-resistant reinforcing steel and ties anchored to the framing. If we find rot behind the wall, we show you before we cover it.
A two-person crew lays brick or stone on a mason's line, cutting with a wet saw and an angle grinder for tight corners and arches. We set weep holes every 24 inches at the base and flash every window head and sill. A typical 400-square-foot wall takes four to six working days.
We tool the mortar joints with a jointing tool while the mortar is still green, then brush and wash the wall down. You get a walkthrough, a photo record of the flashing detail, and a workmanship warranty on the installation.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Keeps every course level and every wall plane straight. A wavy veneer wall is almost always a line that was set wrong on day one.
Cuts brick and stone cleanly for corners, arches, and around windows. A wet saw keeps the cut face from chipping and controls dust.
Brick tongs carry multiple units safely up a ladder or scaffold. The brick hammer splits and trims units for a tight fit at the ends of a course.
Blends Sakrete and Quikrete mortar to a consistent consistency. A mortar hoe gives a better mix than a shovel and keeps the batch uniform.
Shapes the mortar joint while it is still green. The joint profile controls how water sheds off the wall face.
Cuts out failed mortar and shapes replacement joints during repair work. Sharp chisels matter more than people think on old, soft brick.
A 1962 ranch with failing fiber siding on the west wall, rotted sheathing at the base, and no drainage plane behind the original wall. The homeowner was repainting every eight years.
We tore off the siding, replaced the sheathing, installed house wrap and a drainage plane, and set 420 square feet of Glen-Gery brick with new window flashing and weep holes. Six working days on site.
A plain-sided entry with a concrete stoop and no visual anchor. The homeowner wanted stone but was worried about weight and water behind the wall.
We installed 90 square feet of natural stone veneer over a new drainage plane with corrosion-resistant ties, plus a cast stone sill. The wall matches the house trim and drains at the base.
A chimney leaking into the attic for years, with crumbling mortar joints, a cracked crown, and staining down the brick face. The homeowner had patched it twice with caulk.
We rebuilt the crown, repointed the stack with a lime-matched mortar, and flashed the roof-to-chimney joint. The leak stopped, and the brick face cleaned up with a masonry-safe wash.
Most veneer failures in Clackamas County trace back to water. Here are the four we see most, and what we do about them.
Ask a pro →We find the water source first, usually bad flashing or blocked weep holes. Then we replace the spalled units with a matched brick and repoint the surrounding joints. If the damage is widespread, we quote a partial rebuild rather than patching forever.
We trace the moisture path, correct the flashing or drainage detail, and clean the wall with a masonry-safe product. Once the wall can dry, the bloom stops coming back.
We brace and stabilize the wall, then remove and rebuild the detached section with new ties and reinforcing steel set to IBC spacing. We inspect the framing while the wall is open.
We rebuild the crown, repoint the stack with a matched mortar, and flash the roof-to-chimney joint. That combination stops the leak at the top instead of chasing stains inside.
Most residential veneer projects in Milwaukie run $18 to $32 per square foot installed in 2026, so a 400-square-foot wall lands between $7,200 and $12,800. Brick sits at the lower end, natural stone veneer at the upper end. Tear-off of old siding, sheathing repair, and complex flashing around chimneys push the number up. We give you a written range before any work starts.
RenovoBase installs brick, stone, and cast stone veneer across Milwaukie and Clackamas County, including Downtown Milwaukie, Ardenwald, and Milwaukie Heights. We are Oregon CCB licensed and insured, and we have run veneer work here since 2021. Call (855) 947-9500 and we will schedule a walkthrough, usually within the same week.
Yes. We cover all of Milwaukie plus the surrounding ZIP codes 97222 and 97269, and we regularly work in Linwood, Concord, and along the Milwaukie Riverfront. If you are inside Clackamas County, we can be on site for an estimate within a few days. Emergency calls for brick veneer detachment or chimney leaks get priority scheduling.
A typical 400-square-foot wall takes four to six working days once materials are on site. Add two to three days for tear-off and prep if we are removing old siding. Stone veneer runs slightly slower than brick because of the fitting. Weather can add a day here and there, but we do not leave a wall open overnight without covering it.
brick masonry contractorBrick veneer and full brick walls share the same flashing and tie details. If your project needs a structural brick section alongside the veneer, we handle both under one scope and one crew.Explore →
masonry contractors near meSearching for masonry contractors near me Milwaukie usually means you want one team for veneer, repair, and flatwork. We cover all of it, so you are not juggling three subcontractors on one project.Explore →
chimney masonry near meChimneys take the worst weather on the house. We rebuild crowns, repoint stacks, and flash the roof-to-chimney joint as part of any veneer project that touches the chimney chase.Explore →
masonry fireplace contractors near meAn outdoor fireplace uses the same veneer materials as your walls. We build fireboxes, hearths, and chimney caps so the fireplace matches the house instead of looking bolted on.Explore →
masonry restorationWhen tuckpointing and flashing repair can save a wall, restoration is cheaper than replacement. We match historic mortar with lime mortar and portland cement blends to avoid damaging old brick.Explore →
stone masonry contractorNatural stone veneer is heavier and less uniform than brick. We set it with the same drainage plane and ties, but with more cutting and fitting to get tight joints and a natural face.Explore →
emergency masonry repairBrick veneer detachment, a cracked foundation, or a chimney leak after a storm needs a fast response. We tarp, brace, and stabilize first, then quote the permanent repair.Explore →
24/7 masonry contractorStorm damage does not wait for business hours. Our after-hours line handles urgent calls for falling brick, water infiltration, and structural concerns until we can get a crew out.Explore →Call (855) 947-9500 and we will schedule a walkthrough, usually within the same week. You get a written scope, a price range, and a straight answer about whether repair or replacement is the right call. Oregon CCB licensed and insured.
Get Free Estimate (855) 947-9500 →Call (855) 947-9500 or email [email protected] and we will get back to you within one business day. For emergencies, the 24/7 line is always open. We schedule estimates Monday through Friday and can usually be on site the same day you call.